- In ODM, design ownership, tooling ownership and brand ownership are three separate questions, and each needs its own clause.
- If the contract is silent, a factory that started from its own engineering can reasonably claim the design and sell it to others.
- Vietnam is a first-to-file country, so register your trademark and, where relevant, your industrial design with NOIP before samples circulate.
- Practical controls such as split tooling, a partial BOM and holding native CAD files protect you even when a contract is hard to enforce.
When a Vietnamese factory designs a product for you, three things are created at the same time: the design itself, the tooling that makes it, and the brand that sells it. Each one can end up owned by a different party, and the default answer is rarely the one buyers assume. In a typical ODM arrangement the factory starts from its own engineering, so unless the contract says otherwise, it can argue that the drawings, the molds and even the improvements you requested belong to it.
That matters more than it first appears. If the design stays with the factory, the same product can show up under another brand a few months after your launch. If the molds are not clearly yours, moving production to a second supplier can mean paying for tooling twice. If your trademark is not registered in Vietnam, someone else can file it first and make your life difficult at export.
This guide covers the ownership questions to settle before the first sample is made: design ownership models, tooling rights, NNN agreements, trademark and industrial design filings in Vietnam, and practical steps that limit exposure. If you are new to the model, start with how ODM manufacturing in Vietnam works. This article is general information, not legal advice.
Three ownership models you will meet
Most ODM deals fall into one of three patterns. Knowing which one you are in tells you what to negotiate.
Factory-owned design
The factory has an existing product or platform, and you buy it with your branding and a few changes. This is close to private label. The factory keeps the design and can sell the base product to other buyers. You own your logo, your packaging artwork and any unique changes only if the contract says so. Cost of entry is low, but exclusivity is limited.
Buyer-owned design
You commission the factory to design a product for you, pay a design or engineering fee, and receive an assignment of the resulting design rights. The factory is a service provider for the design work. This costs more upfront, since the factory gives up the chance to resell, but it is the only model where you can move production later without a fight. The fee structure is covered in what an ODM project costs.
Shared or licensed design
The factory keeps its core platform, for example a standard mechanism, frame or electronics board, and you own the parts that make the product yours: the exterior, the finish, the specific dimensions. The factory may grant you exclusivity for a market or a period. This is common and workable, but only if the line between “their platform” and “your design” is drawn in writing, ideally with drawings attached.
| Model | Who owns the drawings | Who owns the tooling | Can the factory sell it to others | Typical fit |
|---|---|---|---|---|
| Factory-owned design | Factory | Factory | Yes, except your branding | Fast launch, test a market |
| Buyer-owned design | Buyer, by written assignment | Buyer, if stated in contract | No | Core product, long-term brand |
| Shared or licensed | Split by component or feature | Usually split by part | Only the base platform | Differentiated product on proven base |
The comparison with OEM and contract manufacturing, where the buyer brings the design from the start, is covered in ODM vs OEM vs contract manufacturing.
Tooling ownership is a separate question
Buyers often assume that paying for a mold means owning it. In practice, three situations come up. Tooling paid upfront in full is the cleanest, but ownership still needs to be stated. Tooling split between buyer and factory usually means the factory keeps rights until a volume threshold. Amortized tooling, where the cost is built into the unit price, typically leaves ownership with the factory until an agreed quantity has shipped.
Whatever the structure, the contract should cover these points:
- Ownership statement. Molds, dies, jigs, fixtures, sewing patterns and cutting templates made for your product are your property from the date of payment.
- Marking. Each tool carries a plate or engraving with your company name and a tool number.
- Register and photos. The factory keeps a list of your tools with photos, storage location and expected life, for example shot count for injection molds.
- Maintenance. Who pays for routine maintenance and for repair or replacement once the tool reaches its expected life.
- Exclusive use. Your tools are used only for your orders.
- Release on demand. The factory releases the tools within a stated number of days of a written request, once invoices are settled, and assists with packing for transfer.
NNN agreements: what they cover in practice
A standard NDA stops a factory from telling others about your product. It does not stop the factory from using what it learned to make a similar product itself, and it does not stop it from contacting your customers. An NNN agreement covers all three:
- Non-disclosure. Confidential information is not shared with third parties, including subcontractors, without your consent.
- Non-use. Your information is used only to quote and manufacture for you, not for the factory’s own products or for other buyers.
- Non-circumvention. The factory does not sell your product, or a close copy, directly to your customers or distributors.
For an agreement that can be enforced in Vietnam, a few details matter. Write it under Vietnamese law, in Vietnamese and English, with the Vietnamese version controlling or both versions equal. Name the correct legal entity using its enterprise registration number, not a trade name. Define the product precisely, with drawings or photos attached. Include a liquidated damages figure, because proving actual loss is slow. Choose dispute resolution that can act in Vietnam, such as Vietnamese courts or arbitration seated in Vietnam. A US or EU court judgment is difficult to enforce against a Vietnamese company.
Register your IP in Vietnam before you need it
Vietnam, like most countries, follows a first-to-file principle for trademarks and industrial designs. Whoever files first with the Intellectual Property Office of Viet Nam (NOIP) is generally in the stronger position. Registration in the US, EU or Japan does not protect you in Vietnam on its own.
Trademarks. You can file directly with NOIP through a local agent, or designate Vietnam in an international application under the WIPO Madrid System if you already have a home registration. A Vietnamese trademark is typically protected for 10 years from filing and can be renewed. Examination takes many months, so file as early as possible, ideally before you send artwork to any factory.
Industrial designs. If the product’s appearance is what makes it valuable, consider an industrial design registration. The design must be new, so file before images are published or shown at trade fairs. Vietnamese industrial design protection typically runs 5 years from filing, renewable twice. Vietnam is also part of the Hague system for international design filings.
Customs recordal. Once registered, rights holders can ask Vietnamese customs to monitor exports of suspected infringing goods. This is one of the few practical tools that works at the point of manufacture.
Registration is inexpensive compared with tooling. It should be part of the project budget, not an afterthought.
Send a brief Send your brief
Practical controls that do not depend on a court
Contracts matter, but good structure protects you even when enforcement is slow.
- Split tooling. For multi-part products, have critical components made by a second supplier. No single factory can assemble the full product without you.
- Do not share the full BOM with one party. Keep firmware, a key component, a formulation or the final assembly step with a separate supplier or in your own hands where feasible.
- Hold the master files. Make native CAD files, pattern files and full specifications a paid deliverable, not something the factory keeps on its own server.
- Document your contributions. Keep dated sketches, emails and revision logs showing which features came from you. They matter if ownership is later disputed.
- Release brand assets late. Share logo files and final packaging artwork only when production is confirmed.
What to put in the contract
The table below is a working checklist for your lawyer and for the negotiation with the factory.
| Clause | What it should say |
|---|---|
| Design assignment | All design work created for the project is assigned to the buyer on payment of the design fee |
| Background IP | The factory’s pre-existing platform is listed; the buyer gets a license to use it for its orders |
| Deliverables | Native CAD files, 2D drawings, pattern files and specifications delivered at defined milestones |
| Tooling | Ownership, marking, register, maintenance, exclusive use and release on demand |
| Exclusivity | Scope by product, market and period, if the factory keeps any design rights |
| Confidentiality | NNN terms, including subcontractors and employees |
| Brand use | The factory may not use the buyer’s trademarks or product photos without written consent |
| Dispute resolution | Vietnamese law, bilingual contract, courts or arbitration that can act in Vietnam |
The other clauses to settle before the deposit are listed in ODM manufacturing agreement: 15 clauses.
Red flags during negotiation
- The factory refuses any written design assignment, even for features you created and paid for.
- Tooling is “included” in the unit price with no statement of when ownership transfers.
- The factory insists on keeping native CAD files and offers only PDFs.
- The signing entity is a trading company rather than the factory that will hold your molds.
- Your product photos appear in the factory’s catalog before your launch.
None of these alone means the factory is dishonest. Many Vietnamese ODM factories protect their own engineering for good reasons. What matters is a clear answer, in writing, before samples begin.
How IP fits into matching
When you send a brief through our RFQ form, state which ownership model you expect: factory design with your branding, buyer-owned design, or a shared platform. That shapes which factories are a good fit, since some prefer to sell their own designs and others are set up for commissioned work. On request, we arrange an NDA before your brief is shared with the factories we match. The IP terms themselves, including assignment, tooling and exclusivity, are negotiated and signed directly between you and the factory you choose. For more background on the model itself, see our overview of ODM manufacturing in Vietnam.
Next step
Decide your ownership model, file your trademark in Vietnam, and prepare an NNN draft before the first sample. Then send your brief. We reply within 24 business hours and match you with up to 3 Vietnamese ODM factories that fit your product and your IP expectations.
Frequently asked questions
Who owns the design in an ODM project by default?
There is no safe default. In ODM the factory usually starts from its own platform or engineering, so without a written assignment it can argue the drawings and improvements are its property. If you want to own the design, the contract must say that all design work created for your project, including drawings, CAD files and specifications, is assigned to you on payment of the agreed fee.
If I pay for the molds, do I own them?
Not automatically. Paying for tooling and owning it are different things unless the contract states ownership, marking, storage, maintenance and your right to remove the molds on request. Amortized tooling, where the cost is spread into the unit price, is the most common source of disputes, because ownership often only transfers after a stated number of units.
Do I need to register my trademark in Vietnam if I do not sell there?
It is strongly advisable. Vietnam follows a first-to-file system, so whoever files first generally holds the mark. A registration in Vietnam lets you act against copies made or exported from Vietnam, including through customs recordal. You can file directly with NOIP or designate Vietnam through the WIPO Madrid System if you already have a home registration.
Is an NDA enough to protect my product idea?
An NDA alone is usually too narrow. It stops disclosure but not use of your information to make a competing product, and it rarely covers going around you to your customers. An NNN agreement adds non-use and non-circumvention, and it works best when it is written under Vietnamese law, in Vietnamese and English, with a clear product definition and agreed damages.
Does odmvn.com sign NDAs or negotiate IP terms for me?
No. We review your brief and match you with up to 3 Vietnamese ODM factories that fit. On request, we arrange an NDA before your brief is shared with those factories. Contracts, IP assignments, tooling terms and payments are agreed directly between you and the factory you choose, ideally with advice from your own lawyer.